NBS Voluntary Product StandardU.S. Department of Commerce, National Bureau of Standards, 1972 |
From inside the book
Page
... Wall thickness 2 2223∞∞∞∞ 4 4 4 4 4 4 4 5 5555 or or 5 5 4.4 . Melting point 4.5 . Specific gravity 4.6 . Tensile strength and elongation 4.6.1 . Tubing having an inside diameter of 0.625 inch and over 4.6.2 . Tubing having an ...
... Wall thickness 2 2223∞∞∞∞ 4 4 4 4 4 4 4 5 5555 or or 5 5 4.4 . Melting point 4.5 . Specific gravity 4.6 . Tensile strength and elongation 4.6.1 . Tubing having an inside diameter of 0.625 inch and over 4.6.2 . Tubing having an ...
Page 1
... wall thicknesses ranging from 0.040 inch to 0.070 inch . Type II - This type of PTFE tubing has wall thicknesses ranging from 0.030 inch to 0.055 inch . Type I and Type II include the following classes : Class A - general - purpose ...
... wall thicknesses ranging from 0.040 inch to 0.070 inch . Type II - This type of PTFE tubing has wall thicknesses ranging from 0.030 inch to 0.055 inch . Type I and Type II include the following classes : Class A - general - purpose ...
Page 2
... Wall thickness American wire gage Tolerance ( plus or ( AWG ) Fractional Minimum Maximum Nominal minus ) Number Inch Inch Inch Inch Inch 30 0.010 0.015 0.009 0.002 28 .013 .019 .009 .002 26 .016 .022 .009 .002 24 .020 .027 .012 .003 22 ...
... Wall thickness American wire gage Tolerance ( plus or ( AWG ) Fractional Minimum Maximum Nominal minus ) Number Inch Inch Inch Inch Inch 30 0.010 0.015 0.009 0.002 28 .013 .019 .009 .002 26 .016 .022 .009 .002 24 .020 .027 .012 .003 22 ...
Page 3
... Wall thickness Type I Type II Descriptive Tolerance Tolerance size ( plus or ( plus or Minimum Maximum Nominal minus ) Nominal minus ) Inch Inch Inch Inch Inch Inch Inch 1/16 0.057 0.067 0.040 0.005 0.030 0.004 1/8 .120 .130 .040 .005 ...
... Wall thickness Type I Type II Descriptive Tolerance Tolerance size ( plus or ( plus or Minimum Maximum Nominal minus ) Nominal minus ) Inch Inch Inch Inch Inch Inch Inch 1/16 0.057 0.067 0.040 0.005 0.030 0.004 1/8 .120 .130 .040 .005 ...
Page 4
... wall thickness Inch 0.007 to 0.0089 inclusive 0.009 to 0.0099 inclusive 0.010 to 0.0119 inclusive 0.012 to 0.0149 inclusive 0.015 to 0.0159 inclusive 0.016 to 0.0199 inclusive 0.020 and higher Volts 10,000 11,500 12,500 14,600 15,000 ...
... wall thickness Inch 0.007 to 0.0089 inclusive 0.009 to 0.0099 inclusive 0.010 to 0.0119 inclusive 0.012 to 0.0149 inclusive 0.015 to 0.0159 inclusive 0.016 to 0.0199 inclusive 0.020 and higher Volts 10,000 11,500 12,500 14,600 15,000 ...
Common terms and phrases
accordance with ASTM Almac Plastics American Hospital Association automatic data processing Breden Bunnel Plastics Bureau of Standards Calif Camden Chemical Company Chemplast Chicago compliance conforming Department of Commerce determined in accordance Development of Voluntary dielectric breakdown voltage Dimensions and tolerances direction in accordance effective date electrical Engineering Standards Services Fluorocarbon Government Hewlett Packard IBM Corporation identifying products Inch Inch Inch inclusive industry inside diameter less Institute intended for chemical Lake Shore Drive longitudinal LOOP KNOT mandrel methods of test Minimum proof pressure National Bureau November 15 Office of Engineering Ohio Philadelphia Pittsburgh Poughkeepsie Procedures producer or distributor Products Company provides technical psig PTFE tubing purchaser and seller requirements resin right to depart Roberts and Porter specific gravity specified in table Standard PS 52-71 Standard Reference strength and elongation Technology temperature tensile strength tested in accordance Transverse specimens tubing is intended U.S. Department Voluntary Product Standard Washington