NBS Voluntary Product StandardU.S. Department of Commerce, National Bureau of Standards, 1972 |
From inside the book
Results 1-5 of 5
Page 1
... maximum flexi- bility and fatigue resistance . Class C - stress - relieved tubing - processed for minimum permeability . 3. REQUIREMENTS 3.1 . General Products represented as complying with 1 Scope and Classification Scope 2 Classification.
... maximum flexi- bility and fatigue resistance . Class C - stress - relieved tubing - processed for minimum permeability . 3. REQUIREMENTS 3.1 . General Products represented as complying with 1 Scope and Classification Scope 2 Classification.
Page 2
... maximum of 2 percent by weight of additive is permissible . 3.3 . Dimensions and tolerances - The dimensions and tolerances of the tubing shall be as specified in table 1 or 2 when the tubing is measured in accordance with 4.3 . 1 Later ...
... maximum of 2 percent by weight of additive is permissible . 3.3 . Dimensions and tolerances - The dimensions and tolerances of the tubing shall be as specified in table 1 or 2 when the tubing is measured in accordance with 4.3 . 1 Later ...
Page 3
... Maximum Nominal minus ) Nominal minus ) Inch Inch Inch Inch Inch Inch Inch 1/16 0.057 0.067 0.040 0.005 0.030 0.004 ... maximum weight loss as specified in table 3 when tested in accordance with 4.7 . 3.8 . Dimensional stability - The ...
... Maximum Nominal minus ) Nominal minus ) Inch Inch Inch Inch Inch Inch Inch 1/16 0.057 0.067 0.040 0.005 0.030 0.004 ... maximum weight loss as specified in table 3 when tested in accordance with 4.7 . 3.8 . Dimensional stability - The ...
Page 6
... maximum and minimum wall thicknesses in accordance with 4.3.1 . and 4.3.2 . Place the specimen on a steel mandrel having a diameter from 3 to 6 Tubing having an inside diameter less than 0 090 inch Weight loss 4 4 4 Dimensional stability.
... maximum and minimum wall thicknesses in accordance with 4.3.1 . and 4.3.2 . Place the specimen on a steel mandrel having a diameter from 3 to 6 Tubing having an inside diameter less than 0 090 inch Weight loss 4 4 4 Dimensional stability.
Page 7
... maximum and minimum wall thicknesses at each end in accordance with 4.3.1 and 4.3.2 . The percent change of any dimension shall not exceed that specified in table 3 . 4.9 . Dielectric breakdown voltage - The dielectric breakdown voltage ...
... maximum and minimum wall thicknesses at each end in accordance with 4.3.1 and 4.3.2 . The percent change of any dimension shall not exceed that specified in table 3 . 4.9 . Dielectric breakdown voltage - The dielectric breakdown voltage ...
Common terms and phrases
accordance with ASTM Almac Plastics American Hospital Association automatic data processing Breden Bunnel Plastics Bureau of Standards Calif Camden Chemical Company Chemplast Chicago compliance conforming Department of Commerce determined in accordance Development of Voluntary dielectric breakdown voltage Dimensions and tolerances direction in accordance effective date electrical Engineering Standards Services Fluorocarbon Government Hewlett Packard IBM Corporation identifying products Inch Inch Inch inclusive industry inside diameter less Institute intended for chemical Lake Shore Drive longitudinal LOOP KNOT mandrel methods of test Minimum proof pressure National Bureau November 15 Office of Engineering Ohio Philadelphia Pittsburgh Poughkeepsie Procedures producer or distributor Products Company provides technical psig PTFE tubing purchaser and seller requirements resin right to depart Roberts and Porter specific gravity specified in table Standard PS 52-71 Standard Reference strength and elongation Technology temperature tensile strength tested in accordance Transverse specimens tubing is intended U.S. Department Voluntary Product Standard Washington