NBS Voluntary Product StandardU.S. Department of Commerce, National Bureau of Standards, 1972 |
From inside the book
Results 1-5 of 5
Page 2
... ( ASTM ) D 1457-69 , Standard Specification for TFE- Fluorocarbon Resin Molding and Extrusion Materials , 1 except that a maximum of 2 percent by weight of additive is permissible . 3.3 . Dimensions and tolerances - The dimensions and ...
... ( ASTM ) D 1457-69 , Standard Specification for TFE- Fluorocarbon Resin Molding and Extrusion Materials , 1 except that a maximum of 2 percent by weight of additive is permissible . 3.3 . Dimensions and tolerances - The dimensions and ...
Page 4
... ASTM D 618-61 , Stand- ard Methods of Conditioning Plastics and Electrical Insulating Materials for Testing.2 See footnote 1 , page 2 . 4.3 . Dimensions and tolerances- 4.3.1 . Inside diameter - 4.
... ASTM D 618-61 , Stand- ard Methods of Conditioning Plastics and Electrical Insulating Materials for Testing.2 See footnote 1 , page 2 . 4.3 . Dimensions and tolerances- 4.3.1 . Inside diameter - 4.
Page 5
... ASTM D 1675-65 , Standard Methods of Test- ing Electrical Grade Polytetrafluoroethylene Tubing.3 4.3.2 . Wall thickness - The wall thickness shall be determined in accordance with the procedures described in ASTM D 1675-65 , except that ...
... ASTM D 1675-65 , Standard Methods of Test- ing Electrical Grade Polytetrafluoroethylene Tubing.3 4.3.2 . Wall thickness - The wall thickness shall be determined in accordance with the procedures described in ASTM D 1675-65 , except that ...
Page 6
... ASTM D 1675-65 , except that the minimum weight of the test specimens shall be 50 grams , and the specimens shall be heated in a forced - draft oven for 3 hours at 300 5 ° C ( 572 +9 ° F ) . 4.8 . Dimensional stability - Cut a 10 - inch ...
... ASTM D 1675-65 , except that the minimum weight of the test specimens shall be 50 grams , and the specimens shall be heated in a forced - draft oven for 3 hours at 300 5 ° C ( 572 +9 ° F ) . 4.8 . Dimensional stability - Cut a 10 - inch ...
Page 7
... ASTM D 1675–55 . 4.10 . Low temperature flexibility - Three specimens , each 12 inches long , shall be placed in a circulating - air oven at 200 ± 2 ° C ( 392 ± 4 ° F ) for 5 hours , cooled to room temperature , and then conditioned at ...
... ASTM D 1675–55 . 4.10 . Low temperature flexibility - Three specimens , each 12 inches long , shall be placed in a circulating - air oven at 200 ± 2 ° C ( 392 ± 4 ° F ) for 5 hours , cooled to room temperature , and then conditioned at ...
Common terms and phrases
accordance with ASTM Almac Plastics American Hospital Association automatic data processing Breden Bunnel Plastics Bureau of Standards Calif Camden Chemical Company Chemplast Chicago compliance conforming Department of Commerce determined in accordance Development of Voluntary dielectric breakdown voltage Dimensions and tolerances direction in accordance effective date electrical Engineering Standards Services Fluorocarbon Government Hewlett Packard IBM Corporation identifying products Inch Inch Inch inclusive industry inside diameter less Institute intended for chemical Lake Shore Drive longitudinal LOOP KNOT mandrel methods of test Minimum proof pressure National Bureau November 15 Office of Engineering Ohio Philadelphia Pittsburgh Poughkeepsie Procedures producer or distributor Products Company provides technical psig PTFE tubing purchaser and seller requirements resin right to depart Roberts and Porter specific gravity specified in table Standard PS 52-71 Standard Reference strength and elongation Technology temperature tensile strength tested in accordance Transverse specimens tubing is intended U.S. Department Voluntary Product Standard Washington