Investigation of Performance Characteristics for Sanitary Plumbing FixturesU.S. National Bureau of Standards, 1970 - 68 pages |
From inside the book
Results 1-5 of 19
Page
Institute for Applied Technology (U.S.). Building Research Division. ARCHITECTURE TH 7 .V58 No 22 B 916,961 Project staff . Foreword ... 1. Introduction .. 2. Test. Front Cover.
Institute for Applied Technology (U.S.). Building Research Division. ARCHITECTURE TH 7 .V58 No 22 B 916,961 Project staff . Foreword ... 1. Introduction .. 2. Test. Front Cover.
Page 6
... front apron shall be supported in a continu- ous bed of plaster of paris . For tubs without integral wall surrounds the back ledge of the tub shall be supported by a con- tinuous horizontal 2 - X4 - in wood framing member that is ...
... front apron shall be supported in a continu- ous bed of plaster of paris . For tubs without integral wall surrounds the back ledge of the tub shall be supported by a con- tinuous horizontal 2 - X4 - in wood framing member that is ...
Page 7
... front wall at ultimate load . 5 , 100 At 2,550 lb , center reinforcing member broken . At 3,630 lb , head - end reinforcing member broken . At 4,090 lb , drain - end reinforcing member broken . Transverse cracking of fixture across sump ...
... front wall at ultimate load . 5 , 100 At 2,550 lb , center reinforcing member broken . At 3,630 lb , head - end reinforcing member broken . At 4,090 lb , drain - end reinforcing member broken . Transverse cracking of fixture across sump ...
Page 8
... front rim without damage . The service load simulated is that of a person sitting or standing on the bathtub rim . b . Recommended Test Method ( 1 ) Equipment Required for Test 1. The load - application method shall be as spec- ified in ...
... front rim without damage . The service load simulated is that of a person sitting or standing on the bathtub rim . b . Recommended Test Method ( 1 ) Equipment Required for Test 1. The load - application method shall be as spec- ified in ...
Page 9
... front apron were made . Table 2.3-1 describes some of the lateral - movement measurements made on the various tubs . Since de- flections of the rim and lateral movements of the apron due to an applied load are partly dependent on the ...
... front apron were made . Table 2.3-1 describes some of the lateral - movement measurements made on the various tubs . Since de- flections of the rim and lateral movements of the apron due to an applied load are partly dependent on the ...
Common terms and phrases
abraded abrasion ammonium hydroxide apparatus ASTM designation blisters Bon Ami bottom brush Brush Brush Brush Bureau of Standards cast-iron center deflection cleanability cleaning color Comments on Performance Commercial Standard cracking cycles damage depth detergent dial gage diam Discussion of Existing drain enameled evaluate exposure fixture materials flat specimens FRPE bathtubs FRPE fixtures FRPE specimens gel-coat household chemicals inspection installed iron laboratory manufacturers Mercurochrome National Bureau observed percent Performance Level Performance Requirements plastic polyester porcelain proposed revision Purpose and Scope Rationale for Suggested Rationale for Test Recommended Test Method removal resistance rating sanitary plumbing fixtures sanitary ware Scope The purpose scouring powder scratch scratch test scrub section 2.8 simulate slip resistance slurry soap Sodium soilability soiling agent Spec stain rating Suggested Format sump surface TEFLON temperature test area Test Development test procedure Test Results Tester thermal shock tion vitreous china watch glass weight
Popular passages
Page 4 - In no case does such identification imply recommendation or endorsement by the National Bureau of Standards , nor does it imply that the...
Page 1 - This report gives findings and recommendations developed during an investigation of performance characteristics for sanitary plumbing fixtures, conducted at the request of the Building Research Advisory Board of the National Academy of Sciences-National Research Council. The...