The Code of Federal Regulations of the United States of AmericaU.S. Government Printing Office, 1993 The Code of Federal Regulations is the codification of the general and permanent rules published in the Federal Register by the executive departments and agencies of the Federal Government. |
From inside the book
Results 1-5 of 62
Page 58
... insulation and / or pressure relief valve insulation are supplied with the water heater , then they shall be installed for testing . Clearance shall be provided such that none of the piping contacts other surfaces in the test room ...
... insulation and / or pressure relief valve insulation are supplied with the water heater , then they shall be installed for testing . Clearance shall be provided such that none of the piping contacts other surfaces in the test room ...
Page 61
... insulation having an R value of 4 hr.ft. F / Btu . 4.6 . Ambient Temperature . The ambient air temperature shall be measured approxi- mately at the vertical mid - point of the heater and approximately 2 feet from the surface of the ...
... insulation having an R value of 4 hr.ft. F / Btu . 4.6 . Ambient Temperature . The ambient air temperature shall be measured approxi- mately at the vertical mid - point of the heater and approximately 2 feet from the surface of the ...
Page 96
... insulation and details of installation shall be in accordance with the manufacturer's published recommenda- tion . 3.1.7.2 Control testing conditions for split - type ductless systems . For split - type ductless systems , a single ...
... insulation and details of installation shall be in accordance with the manufacturer's published recommenda- tion . 3.1.7.2 Control testing conditions for split - type ductless systems . For split - type ductless systems , a single ...
Page 141
... ( Insulation of the stack is no longer re- quired for the vented heater test . ) Begin the steady - state performance test by operating the burner and the circulating air blower , on units so equipped , with the adjustments specified by ...
... ( Insulation of the stack is no longer re- quired for the vented heater test . ) Begin the steady - state performance test by operating the burner and the circulating air blower , on units so equipped , with the adjustments specified by ...
Page 181
... Insulation Position : ( 1 ) Exterior Insulation Position means a wall having all or nearly all of its mass exposed to the room air with the insulation on the exterior of that mass . ( 2 ) Integral Insulation Position means a wall having ...
... Insulation Position : ( 1 ) Exterior Insulation Position means a wall having all or nearly all of its mass exposed to the room air with the insulation on the exterior of that mass . ( 2 ) Integral Insulation Position means a wall having ...
Other editions - View all
Common terms and phrases
accordance adjusted Administration agency amended ance ANSI appendix application ASHRAE ASTM average basic model Btu's Btu/h building building envelope burner calculated clothes dryer clothes washer compliance compressor cooking top cooling Daylight defined defrost Department Design Energy determined dry-bulb temperature dwelling units electrical energy energy audit energy conservation energy conservation measures energy consumption Energy Cost Budget energy efficiency Equation Federal financial assistance flue fuel input rate funds grant heat pump heating equipment higher heating value hot water HVAC indoor installed insulation kilowatt-hours Lighting Power manufacturer maximum means measures of energy ment minimum natural gas Office operating outdoor paragraph PCT INT EXT per-cycle percent performance period procedures R-Value ratio Regulations S/BBL Secretary Service specified Standard steady-state subpart sumption Table temperature test conditions thermal thermal transmittance thermostats tion UNCOND SPACE vented heaters wall water heater
Popular passages
Page 528 - State" means any State of the United States, the District of Columbia, the Commonwealth of Puerto Rico, and any territory or possession of the United States; (4) "intercept" means the aural or other acquisition of the contents of any wire, electronic, or oral communication through the use of any electronic, mechanical, or other device.
Page 167 - President, shall have jurisdiction to issue an order requiring such person to appear and give testimony or to appear and produce documents, or both; and any failure to obey such order of the court may be punished by such court as a contempt thereof.
Page 177 - Federal agency" means any department, agency, corporation, or other entity or instrumentality of the executive branch of the Federal Government, including the United States Postal Service, the Federal National Mortgage Association, and the Federal Home Loan Mortgage Corporation. (6) The term "Federal building...
Page 492 - State to provide a program of education beyond secondary education, (3) provides an educational program for which it awards a bachelor's degree or provides not less than a two-year program which is acceptable for full credit toward such a degree...
Page 435 - A house, an apartment or other group of rooms, or a single room, is regarded as a housing unit when it is occupied or intended for occupancy as separate living quarters...
Page 469 - Is a State, a political subdivision of a State, or an agency or Instrumentality of any one or more of the foregoing...
Page 178 - ... the density of the luminous flux incident on a surface; it is the quotient of the luminous flux by the area of the surface when the latter is uniformly illuminated.
Page 542 - Puerto Rico, including but not limited to an individual, partnership, corporation, joint venture, association, or cooperative. For the purpose of...
Page 491 - Indian tribe" means any tribe, band, nation, or other organized group or community of Indians (including any Alaska Native village or regional or village corporation as defined in or established pursuant to the Alaska Native Claims Settlement Act (Public Law 92-203; 85 Stat.
Page 178 - Luminaire: A complete lighting unit consisting of a lamp or lamps together with the parts designed to distribute the light, to position and protect the lamps and to connect the lamps to the power supply.