Index of U.S. Nuclear Standards, Volume 13U.S. Department of Commerce, National Bureau of Standards, 1977 - 119 pages |
From inside the book
Results 1-5 of 21
Page 2
... test method to identify chemicals not requiring classification according to UN GHS (paragraphs 2 and 7); clarifications on the applicability of the BCOP test method to the testing of alcohols, ketones and solids (paragraphs 6 and 7) and ...
... test method to identify chemicals not requiring classification according to UN GHS (paragraphs 2 and 7); clarifications on the applicability of the BCOP test method to the testing of alcohols, ketones and solids (paragraphs 6 and 7) and ...
Page
... test method protocol for the validated reference test method can be obtained at [http://iccvam.niehs.nih.gov]. Testing should be performed at ambient temperature (1725oC) and the components should comply with the following. Test ...
... test method protocol for the validated reference test method can be obtained at [http://iccvam.niehs.nih.gov]. Testing should be performed at ambient temperature (1725oC) and the components should comply with the following. Test ...
Page
Cements, Hydraulic : Sampling, Inspection, and Testing. FEDERAL TEST METHOD STANDARD CEMENTS , HYDRAULIC ; SAMPLING , INSPECTION , AND TESTING Authority . This standard ... Test Method Standard , supported by FED . TEST METHOD STD . NO .
Cements, Hydraulic : Sampling, Inspection, and Testing. FEDERAL TEST METHOD STANDARD CEMENTS , HYDRAULIC ; SAMPLING , INSPECTION , AND TESTING Authority . This standard ... Test Method Standard , supported by FED . TEST METHOD STD . NO .
Page 13
... method; and (iii) the comparable levels of accuracy and reliability, based on what was obtained for the validated test method, that the proposed test method should demonstrate when evaluated using the minimum list of Reference Chemicals ...
... method; and (iii) the comparable levels of accuracy and reliability, based on what was obtained for the validated test method, that the proposed test method should demonstrate when evaluated using the minimum list of Reference Chemicals ...
Page 8
... test specimen with the hood vent in operation . The anemometer shall have an accuracy of ± 0.6 m / min ( ± 2 ft / min ) . 2.4.2 Gas Flow Meters Two calibrated in - line gas flowmeters are required to regulate the ... Test Method Test Setup 4.
... test specimen with the hood vent in operation . The anemometer shall have an accuracy of ± 0.6 m / min ( ± 2 ft / min ) . 2.4.2 Gas Flow Meters Two calibrated in - line gas flowmeters are required to regulate the ... Test Method Test Setup 4.
Other editions - View all
Common terms and phrases
Additional Requirements Alloy Bars Alloy Plate Alloy Seamless Amendment ANSI ANSI ANSI Arc Welding ASME Assembly ASTM Austenitic Austenitic Stainless Steel Carbon Steel Chemical Chromium Chromium-Nickel Columbium Concrete Containment Coolant Corrosion Design Dioxide Powders Dosimeter Electrical Equipment ERDA RDT Evaluating Fast Flux Test Fission Flanges Flux Test Facility Fuel Reprocessing Plants Gamma Graphite Heat Resisting High Temperature Service IEEE Information for Safety Inspection Mass Spectrometric Measuring Method of Test NCRP Neutron Flux NRC RG Nuclear Graphite Nuclear Power Plants Oxide Pipe for High Plutonium Dioxide Plutonium Processing Power Generating Stations Power Plants Revision Pressure Vessel Pressure Vessel Plates Pressurized Water Reactors Processing and Fuel Protection Quality Assurance Radioactive Materials Recommended Practice Safety Analysis Reports Safety Guide Sheathed Sheet Sodium Spec Special Nuclear Material Specification for 1973 Spectrochemical Analysis Standard Steel Pipe Steel Plate Steel Welding Storage Strip Structural Supersedes Systems Thermal Insulation Thermocouple Titanium Uranium Valves Welding Rods Zirconium
Popular passages
Page vii - US Department of Labor, Occupational Safety and Health Administration; 200 Constitution Avenue, NW, Washington, DC 20210. 14. "Review of Emergency Systems," June 1988; US Environmental Protection Agency (EPA), Office of Solid Waste and Emergency Response.
Page vii - American Society of Mechanical Engineers (ASME) 345 East 47th Street New York, New York 10017 American Welding Society, Inc.
Page i - The title of each standard can be found under all the significant key words which it contains. These key words are arranged alphabetically down the center of each page together with their surrounding context. The date of publication or last revision, the standard number, and an acronym designating the standardsissuing organization appear as part of each entry.
Page i - Unit No. NATIONAL BUREAU OF STANDARDS DEPARTMENT OF COMMERCE WASHINGTON, DC 20234 11. Contract/Grant No. 12. Sponsoring Organization Name and Complete Address (Street, City, State, ZIP) 13.