Technical Manual |
From inside the book
Results 1-4 of 4
Page 15
... tooth to be ground , against these index fingers and by means of the knurled nut ( 7 ) , move the link forward or backward until it reaches proper position for sharpening . The position of this knurled nut will govern the amount to be ...
... tooth to be ground , against these index fingers and by means of the knurled nut ( 7 ) , move the link forward or backward until it reaches proper position for sharpening . The position of this knurled nut will govern the amount to be ...
Page 17
... tooth with . the other hand , by means of the elevating handle ( 3 ) until it contacts the grinding wheel and grinds to the desired depth previously regulated . This operation should be done slowly and without unnecessary vibration ...
... tooth with . the other hand , by means of the elevating handle ( 3 ) until it contacts the grinding wheel and grinds to the desired depth previously regulated . This operation should be done slowly and without unnecessary vibration ...
Page 18
... tooth grinding wheel and mount the 1⁄2 inch thick face grinding wheel * on the grinder shaft . The link discarded should be replaced with another , using new rivets . The small anvil block should be used together with the ball pein ...
... tooth grinding wheel and mount the 1⁄2 inch thick face grinding wheel * on the grinder shaft . The link discarded should be replaced with another , using new rivets . The small anvil block should be used together with the ball pein ...
Page 52
... Tooth , Disston 356 2 .30 49 EG - 100-96 Right Cutting Tooth , Disston 355 2 .30 49 EG - 100-97 Center Raker Tooth , Disston 359 2 .25 49 EG - 100-98 EG - 100-99 Right Raker Tooth , Disston 358 1 .30 49 Left Raker Tooth , Disston 357 1 ...
... Tooth , Disston 356 2 .30 49 EG - 100-96 Right Cutting Tooth , Disston 355 2 .30 49 EG - 100-97 Center Raker Tooth , Disston 359 2 .25 49 EG - 100-98 EG - 100-99 Right Raker Tooth , Disston 358 1 .30 49 Left Raker Tooth , Disston 357 1 ...
Other editions - View all
Common terms and phrases
Adjustment Screw Tillotson Air Cleaner Oil breaker plate carburetor chain saw sharpener chain saw teeth chain saw track Choke Body Choke Rod Choke Shutter Combination Drive Connecting Rod COTTER Cotter Pin crank shaft cutting or scoring cutting teeth cylinder designated by G Disston Electric Model End Cap engine USA Spec face angle Fafnir fan housing Fan Hub Flat frame lock screw Gasket gasoline motor grinder base grinder head grinding wheel head assembly hook angle index fingers KB3G knurled nut Lever Magneto Cover Manifold metal base Muffler Name Required Price Oil Reservoir Pierce power chain saw pulley raker teeth Refer to Illustrations remove fan replace saw adjustment fingers saw set saw sharpener unit scoring teeth SCREW SKA set screws Shorting Switch Button SOSSA Spacer Spark Plug Cover STUD swivel head lock Tooth tripod legs U. S. Army V-belt View of Motor WASHER Wrench
Popular passages
Page 2 - MOW (2); Log Comd (2) ; A (5) ; Brig 5 (1) ; Regt 5 (1) ; FT (1); Sch 5 (25); USMA (2) ; PMS & T 5 (1); Gen Dep (2) except Columbus (10); Dep 5 (excluding Engr Sec, Gen Dep) (5), Engr Sec, Gen Dep (2) ; POE (3), OSD (2) ; Ars (2); Engr Dist (1); Mil Dist (1) ; Two (2) copies to each of the following...
Page 2 - E's: 5-157A; 5-267A; 5-279; 5-357; 5-367; 5-621T. NG : One copy to T/O & E units only as listed above. ORC : One copy to T/O & E units only as listed above. For explanation of distribution formula, see SR 310-90-1.
Page 2 - MDW (2); Log Comd (2); A (5); Brig 5 (1); Regt 5 (1); FT (1) ; Sch 5 (25) ; USMA (2) ; PMS & T 5 (1) ; Gen Dep (2) except Columbus (10); Dep 5 (excluding Engr Sec, Gen Dep) (5), Engr sec, Gen Dep (2); POE (3), OSD (3) ; Are (2) ; Engr Dist (1) ; Mil Dist (1) ; Two (2) copies to each of the following T/O & E's: 5-157A; 5-267A; 5-279; 5-357; 5-367; 5-621T.