NIST Special PublicationThe Institute, 2002 |
From inside the book
Results 1-5 of 28
Page v
... Robot Path and Heat Transfer of a TIG - Welded Part with Complex Geometry B4-2 M. Ericsson , University of Trollhattan / Uddevalla , Sweden Dynamic Modeling of GTAW for Rapid Manufacturing ..... 309 Prof. R. Kovacevic , SMU , Richardson ...
... Robot Path and Heat Transfer of a TIG - Welded Part with Complex Geometry B4-2 M. Ericsson , University of Trollhattan / Uddevalla , Sweden Dynamic Modeling of GTAW for Rapid Manufacturing ..... 309 Prof. R. Kovacevic , SMU , Richardson ...
Page 18
... robotic welding . 7. The value of Ip should be set above the spray current level and Tp should be so adjusted that the filler metal tip is melted to a proper size and one droplet is detached appropriately to the base metal during peak ...
... robotic welding . 7. The value of Ip should be set above the spray current level and Tp should be so adjusted that the filler metal tip is melted to a proper size and one droplet is detached appropriately to the base metal during peak ...
Page 29
... Robots & Vision Automation Conference : 23-29 . 32. Nakata S .; Huang J .; Tsuruha Y .. 1988. Visual Sensing System for In - Process Control of Arc Welding Process . Welding International 12 : 1086 to 1090 . 33. Hoffman T .. 1991. Real ...
... Robots & Vision Automation Conference : 23-29 . 32. Nakata S .; Huang J .; Tsuruha Y .. 1988. Visual Sensing System for In - Process Control of Arc Welding Process . Welding International 12 : 1086 to 1090 . 33. Hoffman T .. 1991. Real ...
Page 39
... robotic manufacturers , through the arc tracking of pipeline girth welds in the 5G position is new . The system was successfully used to aid welders in welding over 8200 joints of 42 inch ( 1.06m ) diameter .417 " , .500 ” and .600 ...
... robotic manufacturers , through the arc tracking of pipeline girth welds in the 5G position is new . The system was successfully used to aid welders in welding over 8200 joints of 42 inch ( 1.06m ) diameter .417 " , .500 ” and .600 ...
Page 54
... robot positioning control . Robotic arc welding . Eds . J.D. Lane : 181 to 216 : Springer - Verlag : IFS Publication . Shepard , M.E .; and Cook , G.E. 1992. A frequency - domain model of self - regulation in gas- metal arc welding ...
... robot positioning control . Robotic arc welding . Eds . J.D. Lane : 181 to 216 : Springer - Verlag : IFS Publication . Shepard , M.E .; and Cook , G.E. 1992. A frequency - domain model of self - regulation in gas- metal arc welding ...
Contents
3 | |
21 | |
31 | |
39 | |
47 | |
57 | |
71 | |
79 | |
147 | |
155 | |
173 | |
183 | |
203 | |
211 | |
223 | |
233 | |
87 | |
97 | |
105 | |
117 | |
125 | |
137 | |
241 | |
251 | |
265 | |
281 | |
297 | |
317 | |
Other editions - View all
Common terms and phrases
algorithm analysis angular distortion arc length arc voltage average current background duration boundary butt weldment calculated camera coefficient of variation detachment during peak developed droplet detachment dynamic effect electrode equation experimental Figure filler metal Friction Stir Welding geometry GMAW GMAW-P GTA weld GTAW hoop stress increase interface keyhole laser machine vision martensite material measured mechanical melting metal arc welding method microstructure mm/min mm/s mode molten pool monitoring NIST oscillation frequency peak duration penetration plasma arc welding plate predicted procedure pulsed current resetting residual stress robot rotational sensor shear stress shown in Fig splash strain structure surface technique Technology thermal types of droplet variation VPPAW waveform weld diameter weld fixture weld joint weld pool weld quality welding current Welding Journal welding parameters welding power supply welding process welding simulation welding speed width wire feed speed workpiece zone
Popular passages
Page ii - Certain commercial equipment, instruments, or materials are identified in this paper in order to adequately specify the experimental procedure. Such identification does not imply recommendation or endorsement by the National Institute of Standards and Technology, nor does it imply that the materials or equipment identified are necessarily the best available for the purpose.
Page 94 - Proceedings of the institution of Mechanical Engineers; Part B: Journal of Engineering Manufacture, Vol. 207, pp.9- 1 4, 1 993 [4] Soar RC and Dickens, PM, "Design of Laminated Tooling for High Pressure Die -Casting," Proceedings-SPIE The international society for Optical Engineering, pp.
Page 123 - Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy.