NIST Special PublicationThe Institute, 2002 |
From inside the book
Results 1-5 of 96
Page iii
... Metal Arc Weld Profile Dr. D. M. Barborak , WeldWare Inc. , Columbus , Ohio ............ Weld Penetration Control During GTA Welding Using Weld Pool Oscillation Sensing ........ 71 A2-3 Dr. M. J. M. Hermans , Delft University of ...
... Metal Arc Weld Profile Dr. D. M. Barborak , WeldWare Inc. , Columbus , Ohio ............ Weld Penetration Control During GTA Welding Using Weld Pool Oscillation Sensing ........ 71 A2-3 Dr. M. J. M. Hermans , Delft University of ...
Page viii
... metal arc welding , modeling of weld shape and distortion , modeling of solidification , general modeling , welding documentation , sensing and control of arc quality , droplet control and process automation , automation communication ...
... metal arc welding , modeling of weld shape and distortion , modeling of solidification , general modeling , welding documentation , sensing and control of arc quality , droplet control and process automation , automation communication ...
Page 3
... metal arc welding ( GMAW - P ) is widely used to weld these alloys . However , quality of the weld mainly depends ... metal and 6mm thick AA 5083 Al - Mg alloy base metal were used throughout welding experiments . Electrical signal ...
... metal arc welding ( GMAW - P ) is widely used to weld these alloys . However , quality of the weld mainly depends ... metal and 6mm thick AA 5083 Al - Mg alloy base metal were used throughout welding experiments . Electrical signal ...
Page 4
... metal arc welding ( GMAW - P ) is the most advanced and promising one among various GMA welding processes , for the welding of aluminum and its alloys , because it can greatly improve the weld quality and promote the automation of all ...
... metal arc welding ( GMAW - P ) is the most advanced and promising one among various GMA welding processes , for the welding of aluminum and its alloys , because it can greatly improve the weld quality and promote the automation of all ...
Page 5
... Metal and Base Metal The welding was carried out using solid filler metal ER 5356 Al - Mg alloy having a diameter of 1.2mm and with the compatible AA 5083 Al - Mg alloy of 6.0mm thick base metal . Argon gas having a commercial purity of ...
... Metal and Base Metal The welding was carried out using solid filler metal ER 5356 Al - Mg alloy having a diameter of 1.2mm and with the compatible AA 5083 Al - Mg alloy of 6.0mm thick base metal . Argon gas having a commercial purity of ...
Contents
3 | |
21 | |
31 | |
39 | |
47 | |
57 | |
71 | |
79 | |
147 | |
155 | |
173 | |
183 | |
203 | |
211 | |
223 | |
233 | |
87 | |
97 | |
105 | |
117 | |
125 | |
137 | |
241 | |
251 | |
265 | |
281 | |
297 | |
317 | |
Other editions - View all
Common terms and phrases
algorithm analysis angular distortion arc length arc voltage average current background duration boundary butt weldment calculated camera coefficient of variation detachment during peak developed droplet detachment dynamic effect electrode equation experimental Figure filler metal Friction Stir Welding geometry GMAW GMAW-P GTA weld GTAW hoop stress increase interface keyhole laser machine vision martensite material measured mechanical melting metal arc welding method microstructure mm/min mm/s mode molten pool monitoring NIST oscillation frequency peak duration penetration plasma arc welding plate predicted procedure pulsed current resetting residual stress robot rotational sensor shear stress shown in Fig splash strain structure surface technique Technology thermal types of droplet variation VPPAW waveform weld diameter weld fixture weld joint weld pool weld quality welding current Welding Journal welding parameters welding power supply welding process welding simulation welding speed width wire feed speed workpiece zone
Popular passages
Page ii - Certain commercial equipment, instruments, or materials are identified in this paper in order to adequately specify the experimental procedure. Such identification does not imply recommendation or endorsement by the National Institute of Standards and Technology, nor does it imply that the materials or equipment identified are necessarily the best available for the purpose.
Page 94 - Proceedings of the institution of Mechanical Engineers; Part B: Journal of Engineering Manufacture, Vol. 207, pp.9- 1 4, 1 993 [4] Soar RC and Dickens, PM, "Design of Laminated Tooling for High Pressure Die -Casting," Proceedings-SPIE The international society for Optical Engineering, pp.
Page 123 - Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy.