NIST Special PublicationThe Institute, 2002 |
From inside the book
Results 1-5 of 52
Page
... elements at Boulder , CO . Building Materials Building Environment Fire Safety Engineering • Fire Science Information Technology Laboratory Mathematical and Computational Sciences2 • Advanced Network Technologies • Computer Security ...
... elements at Boulder , CO . Building Materials Building Environment Fire Safety Engineering • Fire Science Information Technology Laboratory Mathematical and Computational Sciences2 • Advanced Network Technologies • Computer Security ...
Page v
... Element Analysis of Creep Strength Mis - matched Dissimilar Welded Joints H. Chen , Southwest Jiaotong University , Chengdu , China ......... 281 ...... Chair : Dr. D. F. Farson , The Ohio State University , Columbus , Ohio Session B3 ...
... Element Analysis of Creep Strength Mis - matched Dissimilar Welded Joints H. Chen , Southwest Jiaotong University , Chengdu , China ......... 281 ...... Chair : Dr. D. F. Farson , The Ohio State University , Columbus , Ohio Session B3 ...
Page 24
... Elements Bordering the Middle Part of a Weld Pool Removal of the Middle Part of a Weld Pool Adaptive Operator Edge Enhancement Sobel Edge Enheancement Prewitt Gradient Edge Enhancement Binary an Image Binary Opening and Closing ...
... Elements Bordering the Middle Part of a Weld Pool Removal of the Middle Part of a Weld Pool Adaptive Operator Edge Enhancement Sobel Edge Enheancement Prewitt Gradient Edge Enhancement Binary an Image Binary Opening and Closing ...
Page 86
... element for uniform full penetration welding ' , Schweissen und Schneiden , Vol . 52 , No. 10 , 2000 , E228 - E231 . 10. H. Wohlfahrt , K. Thomas and S. Wiesner ; ' Welding voltage measurements during TIG and MIG welding with the ...
... element for uniform full penetration welding ' , Schweissen und Schneiden , Vol . 52 , No. 10 , 2000 , E228 - E231 . 10. H. Wohlfahrt , K. Thomas and S. Wiesner ; ' Welding voltage measurements during TIG and MIG welding with the ...
Page 111
... elements in the hidden layer is experimentally determined as six based on the training results for the model . The keyhole size may be regulated by adjusting the wire feed speed and the heat input may be controlled by changing the ...
... elements in the hidden layer is experimentally determined as six based on the training results for the model . The keyhole size may be regulated by adjusting the wire feed speed and the heat input may be controlled by changing the ...
Contents
3 | |
21 | |
31 | |
39 | |
47 | |
57 | |
71 | |
79 | |
147 | |
155 | |
173 | |
183 | |
203 | |
211 | |
223 | |
233 | |
87 | |
97 | |
105 | |
117 | |
125 | |
137 | |
241 | |
251 | |
265 | |
281 | |
297 | |
317 | |
Other editions - View all
Common terms and phrases
algorithm analysis angular distortion arc length arc voltage average current background duration boundary butt weldment calculated camera coefficient of variation detachment during peak developed droplet detachment dynamic effect electrode equation experimental Figure filler metal Friction Stir Welding geometry GMAW GMAW-P GTA weld GTAW hoop stress increase interface keyhole laser machine vision martensite material measured mechanical melting metal arc welding method microstructure mm/min mm/s mode molten pool monitoring NIST oscillation frequency peak duration penetration plasma arc welding plate predicted procedure pulsed current resetting residual stress robot rotational sensor shear stress shown in Fig splash strain structure surface technique Technology thermal types of droplet variation VPPAW waveform weld diameter weld fixture weld joint weld pool weld quality welding current Welding Journal welding parameters welding power supply welding process welding simulation welding speed width wire feed speed workpiece zone
Popular passages
Page ii - Certain commercial equipment, instruments, or materials are identified in this paper in order to adequately specify the experimental procedure. Such identification does not imply recommendation or endorsement by the National Institute of Standards and Technology, nor does it imply that the materials or equipment identified are necessarily the best available for the purpose.
Page 94 - Proceedings of the institution of Mechanical Engineers; Part B: Journal of Engineering Manufacture, Vol. 207, pp.9- 1 4, 1 993 [4] Soar RC and Dickens, PM, "Design of Laminated Tooling for High Pressure Die -Casting," Proceedings-SPIE The international society for Optical Engineering, pp.
Page 123 - Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy.