NIST Special PublicationThe Institute, 2002 |
From inside the book
Results 1-5 of 50
Page
... applied research in the physical sciences and engineering , and develops measurement techniques , test methods , standards , and related services . The Institute does generic and precompetitive work on new and advanced technologies ...
... applied research in the physical sciences and engineering , and develops measurement techniques , test methods , standards , and related services . The Institute does generic and precompetitive work on new and advanced technologies ...
Page v
... Applying WELDSIM H. G. Fjær , Institute for Energy Technology , Norway ........ 251 ..... B2-2 A Computational Model for Heat Affected Zone of Reactor Pressure Vessel Steel Dr. J.-S. Kim , Korea Power Engineering Co. , Korea 265 B2-3 ...
... Applying WELDSIM H. G. Fjær , Institute for Energy Technology , Norway ........ 251 ..... B2-2 A Computational Model for Heat Affected Zone of Reactor Pressure Vessel Steel Dr. J.-S. Kim , Korea Power Engineering Co. , Korea 265 B2-3 ...
Page viii
... applied to welded fabrication and manufacturing . Expert advice was provided in process selection , consumable selection , and welding procedure generation and interpretation of standards . Proceedings are available through Woodhead ...
... applied to welded fabrication and manufacturing . Expert advice was provided in process selection , consumable selection , and welding procedure generation and interpretation of standards . Proceedings are available through Woodhead ...
Page 8
... applied to the molten filler metal tip is not directed to the base metal . Note that in this zone the value of Ip is smaller than 168 A , which is 18A higher than spray current level of 150A with 1.2mm diameter ER 5356 Al - Mg filler ...
... applied to the molten filler metal tip is not directed to the base metal . Note that in this zone the value of Ip is smaller than 168 A , which is 18A higher than spray current level of 150A with 1.2mm diameter ER 5356 Al - Mg filler ...
Page 25
... applied on the droplet , resonance will occur . In this case , the droplet may detach if the magnitude of the force due to resonance is high enough . The essence of this approach is to convert the electrical energy from a welding ...
... applied on the droplet , resonance will occur . In this case , the droplet may detach if the magnitude of the force due to resonance is high enough . The essence of this approach is to convert the electrical energy from a welding ...
Contents
3 | |
21 | |
31 | |
39 | |
47 | |
57 | |
71 | |
79 | |
147 | |
155 | |
173 | |
183 | |
203 | |
211 | |
223 | |
233 | |
87 | |
97 | |
105 | |
117 | |
125 | |
137 | |
241 | |
251 | |
265 | |
281 | |
297 | |
317 | |
Other editions - View all
Common terms and phrases
algorithm analysis angular distortion arc length arc voltage average current background duration boundary butt weldment calculated camera coefficient of variation detachment during peak developed droplet detachment dynamic effect electrode equation experimental Figure filler metal Friction Stir Welding geometry GMAW GMAW-P GTA weld GTAW hoop stress increase interface keyhole laser machine vision martensite material measured mechanical melting metal arc welding method microstructure mm/min mm/s mode molten pool monitoring NIST oscillation frequency peak duration penetration plasma arc welding plate predicted procedure pulsed current resetting residual stress robot rotational sensor shear stress shown in Fig splash strain structure surface technique Technology thermal types of droplet variation VPPAW waveform weld diameter weld fixture weld joint weld pool weld quality welding current Welding Journal welding parameters welding power supply welding process welding simulation welding speed width wire feed speed workpiece zone
Popular passages
Page ii - Certain commercial equipment, instruments, or materials are identified in this paper in order to adequately specify the experimental procedure. Such identification does not imply recommendation or endorsement by the National Institute of Standards and Technology, nor does it imply that the materials or equipment identified are necessarily the best available for the purpose.
Page 94 - Proceedings of the institution of Mechanical Engineers; Part B: Journal of Engineering Manufacture, Vol. 207, pp.9- 1 4, 1 993 [4] Soar RC and Dickens, PM, "Design of Laminated Tooling for High Pressure Die -Casting," Proceedings-SPIE The international society for Optical Engineering, pp.
Page 123 - Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy.