Experimental Determination of Eccentricity of Floor Loads Applied to a Bearing WallU.S. Government Printing Office, 1968 - 6 pages The eccentricity of the loads applied to a specially calibrated compressive strut simulating a brick bearing wall was experimentally determined for a variety of bearing materials and conditions of contact. In one series of tests, an I-beam was bedded in high strength gypsum plaster, bonded and unbonded. For the unbonded plaster bed the eccentricity ratio increased with the applied load to a maximum value of about 0.42, while for the bonded plaster bearing this ratio decreased to an average value of about 0.24 at the maximum load. In the second series of tests the eccentricity was observed for an I-beam supported on neoprene rubber pads, capped and uncapped, of different thicknesses, and of different bearing length. In general the eccentricity ratio increased slightly with the applied load. Lack of intimate contact between the I-beam and the rubber pad 1/8 in. thick resulted in an eccentricity ratio of about 0.40, or nearly the same as for unbonded plaster bearing. Intimacy of contact produced by plaster capping resulted in a marked reduction in the eccentricity ratio to about 0.29; the confinement of the bearing length of the rubber pad to one-half of that used in previous tests and placing it at the extreme end of the beam, further reduced the eccentricity ratio to about 0.18, and to 0.13 for a rubber pad 0.25 in. thick. (Author). |
From inside the book
Results 1-3 of 3
Page
... center line of the strut . It should be added that the strain values given in figure 2 were those obtained from the lower set of strain gages , since they yielded a more consistent relationship than the top gages . The departure of the ...
... center line of the strut . It should be added that the strain values given in figure 2 were those obtained from the lower set of strain gages , since they yielded a more consistent relationship than the top gages . The departure of the ...
Page
... center line of the supporting strut . The arrangement of sup- ports and the load are shown in figure 3 , along with the device for measuring the rotation of the beam end at the strut . This measurement was an ap- proximation based on ...
... center line of the supporting strut . The arrangement of sup- ports and the load are shown in figure 3 , along with the device for measuring the rotation of the beam end at the strut . This measurement was an ap- proximation based on ...
Page
... center line of the pier was taken as the center line of the compressive strut . 2. Both rigid and resilient bearing m such as gypsum plaster and neoprene rubb used to support an I - beam as a floor membe 3. For an unbonded plaster ...
... center line of the pier was taken as the center line of the compressive strut . 2. Both rigid and resilient bearing m such as gypsum plaster and neoprene rubb used to support an I - beam as a floor membe 3. For an unbonded plaster ...
Common terms and phrases
15 cents Annual subscription Applied Technology ArĀ² beam end bearing length bearing materials bearing pad bearing surfaces bonded plaster bearing brick masonry Building Science Series Bureau of Standards Cement and Concrete center line Clearinghouse compressive strut Concrete Properties DEPARTMENT OF COMMERCE Determination of Eccentricity e/t ratio eccen eccentrically applied load eccentrically loaded eccentricity of applied Eccentricity of Floor Eccentricity of Reaction eccentricity ratio increased Emax Emin epoxy Experimental Determination extruded clay brick floor beams Floor Load Government Printing Office high strength gypsum I-beam supported Institute for Applied Interrelations Between Cement intimate contact load applied load bearing wall masonry wall micrometer dial National Bureau neoprene rubber pad Omax physical measurement RADIANS shown in figure SIDE H solid extruded clay span lengths strain gages strength gypsum plaster Superintendent of Documents supported on neoprene supporting force U.S. DEPARTMENT U.S. Government Printing unbonded plaster unbonded plaster bearing value of e/t values of eccentricity Washington